Amintra™ Glutathione Resin

Amintra™ Glutathione Affinity Resin

Amintra™ Glutathione resin is designed for rapid one-step purification of glutathione S-transferase-tagged proteins from bacteria, yeast, insect and mammalian cultures.

Glutathione is covalently coupled to a high crosslinked agarose matrix that provides a high chemical and physical stability and excellent flow rates. The resin is made in the particle size range of 40-165 μm and has a dynamic binding capacity of 10 mg recombinant GST/ml resin.

Amintra™ Glutathione is stable with all commonly used buffers and reagents including 0.1M NaOH and organic solvents. Removal of the GST tag can be performed whilst the fusion protein is bound to the column or in solution after elution.

Discover more about affinity purification with our downloadable guide

Characteristics

MatrixAgarose
Functional groupHeparin of porcine origin
Ligand density4 - 5 mg/ml
Particle size50 - 150 µm
pH stability4-13 (short term) and 4-12 (long term)
Working temperature+4°C to +30°C
Chemical stabilityCompatible with commonly used buffers,
6M guanidine-HCl, 8 M urea
Storage0.05 M sodium acetate in 20% denatured
ethanol

Click to read more

1. What is the shelf-life of Amintra Glutathione resin?
The resin is guaranteed for 12 months after the date of manufacture provided they are stored at 2-8˚C.

2. Do I need to filter the buffers prepared in my laboratory?
It is good laboratory practice to filter all buffers using a 0.45 micron filter.

3. How should I prepare my buffer the Amintra Glutathione resin?
Elution buffers, in particular, should be prepared fresh before use. Reduced glutathione gradually becomes oxidized in solution. It is recommended that you add fresh reduced glutathione and/or other reducing agents to the elution buffer just prior to use. You will need need to re-adjust pH of the buffer system after addition of reduced glutathione.

4. How should I prepare my sample the Amintra Glutathione resin?
It is recommended that all samples are filtered to at least 0.45 µm pore size.

5. Should I add b-mercaptoethanol or DTT to the lysis buffer?
Concentrations less than or equal to 10 mM βmercaptoethanol or DTT can be used with this resin.

6. Should I be concerned if the resin partially dried out during the chromatographic steps?
The resin is robust. Partially dried resin rehydrates rapidly. There are no adverse effects upon the performance of the resin.

7. Do I need to remove the GST-tag from the recombinant protein?
Typically a protease cleavage site is engineered between the GST-tag and the target protein. The GST-tag can be cleaved on the column or in solution after elution. Cleavage of the GST tagged protein on the column eliminates the need to separate the protein from the GST tag at a later date as the GSTtag remains bound to the column. When protein precipitation is observed during cleavage Expedeon’s Stabil-PAC (# STP) can be used to maintain protein solubility.

8. What are the endotoxin levels in the resin?
The endotoxin levels are below the detection levels.

9. Do you have any data regarding ligand leakage?
Ligand leakage, at the point of coupling, is negligible.

10. Can I regenerate the resin?
Regenerate the column by passing 5 CVs of 0.1 M Tris/HCl buffer, 0.5 M NaCl, pH 8.5, then 5 CVs of 0.1 M sodium acetate buffer, 0.5 M NaCl, pH 4.5 and finally 5 CVs of either 1X PBS buffer pH 7.2 or running buffer. Alternatively, use 3 CVs of either 6M Guanidine HCl, 70% ethanol or 0.1M NaOH for cleaning followed with at least 5 CVs of either 1X PBS buffer pH 7.2 or running buffer.

11. Can I re-use the resin?
The resin can be re-used. Re-use does depend on the properties of your target protein. You may observe that flow rates slow down in successive bind-washelute cycles as more samples are progressively loaded on to the columns. In addition, if the resin is not regenerated, binding capacity may be reduced.

You may also be interested in